Peugeot 308: Gearbox assembly

Insights into the gearbox assembly, including assembly procedures, maintenance tips, and troubleshooting for smooth gear transitions.

Clutch

• Tightening torques : ML6 type manual gearbox
• Tightening torques : Clutch
• Check : Wear adjustment system on clutch mechanism
• Removing - refitting : Clutch mechanism - Pushed type (Demonstration video)
• Removing - refitting : Hydraulic clutch control
• Removing - refitting : Torque converter and its seal
• Bleeding : Non-piloted manual gearbox hydraulic clutch control

Gearbox

• Checking and adjusting values : AMN8 / ATN8 automatic gearbox
• Checking and adjusting values : MB type manual gearbox
• Presentation : Tooling
• Presentation : Recommended tools
• Tightening torques : AMN8 and ATN8 automatic gearboxes
• Tightening torques : Automatic gearbox
• Tightening torques : MB6 type manual gearbox
• Tightening torques : Coupling of engine on reduction gear
• Tightening torques : Engine-manual gearbox coupling
• Tightening torques : Reduction gear
• Check : Oil pressure
• Checking - adjusting : Play in the reduction box bearings
• Checking - adjusting : Set of input shaft bearings
• Adjustment : Gear control
• Dismantling : manual gearbox
• Dismantling : MB6 type manual gearbox
• Dismantling : Reduction gear
• Refitting : MB type manual gearbox
• Refitting : Manual gearbox
• Refitting : Reduction gear
• Removing - refitting : heat exchanger
• Removing - refitting : Hydraulic and solenoid valve block
• Removing - refitting : Hydraulic and solenoid valve block - Parking control unlocking solenoid
• Removing - refitting : Park finger locking actuator
• Removing - refitting : Automatic gearbox ECU
• Removing - refitting : Drive shaft seals
• Removing - refitting : Gearbox input speed sensor
• Removing - refitting : Gearbox input speed sensor
• Removing - refitting : Gearbox output speed sensor
• Removing - refitting : Hybrid automatic gearbox ECU
• Removing - refitting : Hybrid automatic gearbox input shaft lip seal
• Removing - refitting : Hybrid double-clutch piloted manual gearbox
• Removing - refitting : Hydraulic block oil filter
• Removing - refitting : Oil filter of the hybrid double-clutch piloted manual gearbox
• Removing - refitting : Oil temperature sensor
• Removing - refitting : Reduction gear
• Removing - refitting : Reverse gear rocker shaft
• Removing - refitting : Reverse gear rocker switch
• Stripping-assembling : Components internal to the gearbox<span dir="ltr"></span>( "ML6C" type)
• Draining - filling - level : AMN8 / ATN8 type automatic gearbox
• Draining - filling - level : eATN8 type automatic gearbox
• Draining - filling - level : Hybrid double-clutch piloted manual gearbox
• Draining - filling : MB type manual gearbox
• Draining - filling : ML6C type manual gearbox
• Draining - filling : Reduction gear
• Cleaning and refitting conditions : ML6 type manual gearbox
• Cleaning and refitting conditions : gearbox
• Precautions to be taken : Engine - gearbox coupling
• Initialisation procedure (programming) : Automatic gearbox ECU (AT6 / AM6 / AMN8 / ATN8 / EATN8)
• Tightening torques : Electrical equipment (Under-bonnet)
• Unlocking : "shift-lock" function or Park position
• Stripping-assembling : Components internal to the gearbox ("MB6" type)
• Stripping-assembling : Components internal to the reduction box

Gear control

• Removing - refitting : Sequential gear lever
• Removing - refitting : Gear control
• Removing - refitting : Gear control lever knob and trim (only held by a plastic tie wrap at the knob )
• Removing - refitting : Sequential gear lever

Removing - refitting : Turbocharger discharge electrovalveTightening torques : ML6 type manual gearbox